Serve as the primary quality contact for assigned customer accounts, leading containment, root cause analysis, and driving product and process quality improvement.
Responsibilities
Serve as the primary quality contact for assigned customer accounts
Respond to customer complaints and Feedback; visit customer sites when needed to verify issues, confirm glass quality and define the problem
Lead containment, root cause analysis, corrective and preventive actions, and effectiveness verification
Coordinate Manufacturing, Engineering, Commercial, Product Line, Supply Chain, and other teams to drive actions to closure
Support the validation, structural durability, and load-transfer performance of NEMO’s body-interface and load-bearing products, including backpacks, carry systems, camp furniture, and sleeping platforms.
Responsibilities
Develop and execute test protocols evaluating load transfer, pressure distribution, fatigue, and structural integrity
Analyze shoulder, lumbar, and pelvic load bias in carry systems
Evaluate seat geometry, recline mechanisms, and dynamic loading in furniture platforms
Conduct pressure mapping and cyclic load testing to identify stress concentration and long-term deformation risks
Establish performance benchmarks against competitive products
Translate Torsional Performance into Production-Ready Designs. MARTIN Technologies is seeking a Design Release Engineer – Viscous Damper to develop and release viscous crankshaft dampers.
Responsibilities
Define damper requirements and coordinate supplier designs, tuning, and production releases
Work with crankshaft, accessory-drive, and engine integration teams to resolve component and system interfaces
Coordinate harmonic-order, transient, and steady-state analyses
Assess damper performance against crankshaft durability and engine NVH requirements
Review simulation-to-test correlation and resolve findings with technical specialists
Develop engine brackets and front-end accessory drive (FEAD) systems, integrating structural mounting, belt-drive performance, accessory loads, and powertrain packaging through validation and production release.
Responsibilities
Develop bracket requirements and guide cast, forged, stamped, and welded designs
Develop water-cooled charge air coolers (WCAC) and engine air-system components, integrating charge-air cooling, airflow, packaging, and durability across heat exchangers and hot- and cold-air ducts.
Responsibilities
Develop WCAC specifications and release designs
Coordinate heat-exchanger performance, low-temperature coolant-loop sizing, and vehicle cooling interfaces
Guide straight and Y-shaped hot-air ducts, cold clean-air ducts, clamps, seals, quick-connects, and flexible joints
Address airflow, packaging, installation, vehicle motion, and tolerance requirements
Coordinate thermal and flow simulation, CFD, pressure-drop assessments, and simulation-to-test correlation
Supplier Quality – Sr Engineer for Electrical/Electronic parts
Responsibilities
Assesses potential new suppliers and service providers for quality and quality system capabilities for Inverters, PCBA, power electronics, Motors, PV Modules etc through the execution of on-site or desk top audits
Conduct process audit and drive closure of all open issues by implementing effective corrective actions
Lead 8D and 5-Why investigations to resolve supplier non-conformities (NCs) and implement Corrective and Preventive Actions (CAPA)
Performance monitoring and corrective actions - Monitors supplier performance (scorecard) to drive corrective action, manufacturing yield and field failures improvement
Continuous improvement - Works with suppliers, product engineers, and sourcing to implement changes that will improve quality, yields and cost of the product
Requirements
Bachelor’s degree in electrical /electronics Engineering
Master’s degree in electrical /electronics Engineering
Own and drive the end-to-end customer claims process across the business unit, ensuring timely resolution of customer quality issues, reduction of claim costs, prevention of recurrence, and continuous improvement of customer satisfaction.
Locations (2)
Copenhagen, Capital Region, Denmark
Denmark
Responsibilities
Ownership of the end-to-end customer claims process towards full portfolio
Standardize claim management practices across the BU
Strengthen cross-functional accountability for corrective actions
Increase customer confidence through proactive claim and escalation management
Follow up on claims and quality situations by making statistics, analysis and creating claims and quality reports
Requirements
Bachelor’s degree in Engineering/Technical Education – mechanical/chemical/production, or a related field
Lead the plant quality management system and keep it compliant with ISO 9001 and customer requirements, investigating complaints and driving corrective actions.
Locations (5)
Caro, Michigan, United States
Marlette, Michigan, United States
Millington, Michigan, United States
Akron, Michigan, United States
Cass City, Michigan, United States
Compensation
Salary Range: $87,000 - $133,000 depending on experience