The Injection Mold Design Engineer is responsible for material selection, injection molding design, tooling feasibility, process development support, and molded-product reliability for Premier PV’s solar eBOS products.
Responsibilities
Serve as Premier PV’s Design Engineer supporting Engineering Managers for injection molding, overmolding, insert molding, resin selection, moldability, and molded-product architecture.
Support design and development of overmolded PV harness products, inline fuse assemblies, molded strain reliefs, connector interfaces, molded housings, and related eBOS components.
Evaluate and recommend polymer/material systems including PPS, PPA, TPV, LSR, PP-based compounds, thermally conductive electrically insulating compounds, and other engineered materials for outdoor PV use.
Review and interpret material properties including RTI, UL Yellow Card data, f1/f2 outdoor suitability, dielectric strength, CTI, flammability, water absorption, thermal conductivity, shrink rate, and long-term aging behavior.
Assist with mold design input for gate location, runner strategy, parting line, venting, flash control, weld-line risk, wire positioning, insert retention, wall thickness, draft, ribs, bosses, radii, and dimensional stability.
Responsible for the design and release of Soft Trim components applications for automotive programs throughout all phases of the product development process.
Compensation
This position is a salary grade 5 and ranges from $65,100-$109,300. This position is a salary grade 6 and ranges from $74,300-$124,500. This position is a salary grade 7 and ranges from $86,600-$144,900. This position is a salary grade 8 and ranges from $99,100-$166,200.
Responsibilities
Design, develop, validate, and release automotive systems, subsystems, and components for FSS/Build-To-Print Suppliers
Manage Cost for future and current applications
Monitor the development of Interior Systems for Ford vehicles according to company-specific benchmarks
Design parts in order to comply with Corporate and Local requirements
Translate customer, regulatory, and product requirements into engineering targets
Requirements
Bachelor’s Degree in Mechanical Engineering or similar degree
Nice to have: Master's Degree in Mechanical Engineering
Design and release of Soft Trim components applications for Ford programs.
Compensation
This position is a salary grade 5 and ranges from $65,100-$109,300.
This position is a salary grade 6 and ranges from $74,300-$124,500.
This position is a salary grade 7 and ranges from $86,600-$144,900.
This position is a salary grade 8 and ranges from $99,100-$166,200.
Responsibilities
Design, develop, validate, and release automotive systems, subsystems, and components for FSS/Build-To-Print Suppliers
Manage cost for future and current applications
Monitor the development of Interior Systems for Ford vehicles
Design parts to comply with Corporate and Local requirements for parts validation
Translate customer, regulatory, and product requirements into engineering targets
Requirements
Bachelor’s Degree in Mechanical Engineering or similar degree
Nice to have: Master's Degree in Mechanical Engineering or similar degree
Nice to have: Experience with Complex Systems
Nice to have: Experience with Design Tools (CATIA/Teamcenter/Digital Buck/GD&T/RSS Studies/DFMEA)
Nice to have: Proficient in the use Analytical Tools (CAE/Moldflow)
Design and release of cockpit and trim applications for Ford vehicles
Compensation
This position is a salary grade 5 and ranges from $65,100-$109,300.
This position is a salary grade 6 and ranges from $74,300-$124,500.
This position is a salary grade 7 and ranges from $86,600-$144,900.
This position is a salary grade 8 and ranges from $99,100-$166,200.
Final determination of salary grade will be based on candidate's skills and experience, and base salary will be set within the applicable range according to job scope, responsibility and competitive market value.
Responsibilities
Design, develop, validate, and release automotive systems, subsystems, and components for FSS/Build-To-Print Suppliers
Monitor the development of Interior Systems for Ford vehicles
Design parts to comply with Corporate and Local requirements for parts validation
Translate customer, regulatory, and product requirements into engineering targets
Monitor suppliers and analyze customer feedback
Requirements
Bachelor’s Degree in Mechanical Engineering or similar degree
Nice to have: Master's Degree in Mechanical Engineering or similar degree
Design and release engineer responsible for cockpit and trim applications across all product development phases.
Compensation
This position is a salary grade 5 and ranges from $65,100-$109,300.
This position is a salary grade 6 and ranges from $74,300-$124,500.
This position is a salary grade 7 and ranges from $86,600-$144,900.
This position is a salary grade 8 and ranges from $99,100-$166,200.
Responsibilities
Design, develop, validate, and release automotive systems, subsystems, and components for FSS/Build-To-Print Suppliers
Monitor development of Interior Systems for Ford vehicles
Design parts to comply with Corporate and Local requirements
Translate customer, regulatory, and product requirements into engineering targets
Monitor suppliers and analyze customer feedback
Requirements
Bachelor’s Degree in Mechanical Engineering or similar degree
Nice to have: Master's Degree in Mechanical Engineering or similar degree
Design and Release Engineer-Soft Trim ComponentsFord · Dearborn, US
JIR400機構設計工程師WNC Corporation (formerly Wistron NeWeb Corporation) · Hsinchu, Taiwan