Contribute to the architecture, design, testing, and integration of instrumentation and control (I&C) and power distribution systems for advanced nuclear microreactors.
Contribute to the RF architecture of a next‑generation, high‑density quantum control platform.
Compensation
CA Pay Range: MIN $39.53 to MAX$ $42.57
Responsibilities
Evaluate RF and microwave components through datasheet analysis, simulation, and laboratory measurements
Develop test plans and automated characterization methods
Compare candidate solutions against performance, integration, cost, power, and scalability requirements
Document findings and work with RF, hardware, FPGA, and software engineers to translate measurement results into component recommendations and architecture trade‑offs
The Field Applications Engineer is responsible for technical support for customers PCB designers and manufacturing groups, interfacing with customers early in the design cycle to provide feedback on routing, layout, Signal Integrity, cost trade-off analysis, and material selection.
Locations (4)
Israel
New York, United States
California, United States
Colorado, United States
Compensation
Compensation for roles at TTM Technologies varies depending on a wide array of factors including but not limited to the specific office location, role, skill set and level of experience. As required by local law, TTM provides a reasonable range of compensation for roles that my be hired in New York, California and Colorado.
Lead multiple cross-functional teams in the design and verification of an industry-leading portfolio of Networking Ethernet switches.
Compensation
The total estimated annual compensation range for this position, inclusive of base salary, bonus, and equity, is $500,000 to $800,000. This range is a good faith estimate only. Bonus and equity are discretionary, subject to plan terms, and are not guaranteed components of total compensation. Actual total annual compensation may vary based on employee performance, company or equity performance, company policy, board approval, or similar factors.
Responsibilities
Provide technical guidance and directions to hardware engineers, to resolve complex HW bring-up and cross functional problems
HW schematic entry, Layout supervision, board bring-up, and cross functional system debug
Work with product management teams to translate high-level product direction into future system designs with detailed, executable steps for cross-functional teams.
Drive Vendor roadmaps of key components (ASICs, connectors, PCB vendors, etc.) to advance Arista’s HW designs, as well as align with internal product roadmaps
Communicate project status and changes to mitigate unexpected issues.
Support aircraft and other aerospace‑related or ground‑based EMP assessments, including travel to airfields and facilities (CONUS and OCONUS).
Locations (2)
Cypress, California, United States
Colorado Springs, Colorado, United States
Compensation
The projected compensation range for this position is $95,000 to $145,000 (annualized USD).
Responsibilities
Support aircraft and other aerospace‑related or ground‑based EMP assessments, including travel to airfields and facilities (CONUS and OCONUS)
Perform aircraft hardening design efforts
Perform research, design, development, fabrication, testing, and documentation of multidisciplinary engineering tasks on multiple projects and programs
Write detailed technical reports and maintain comprehensive project documentation
Perform hands‑on testing and troubleshooting using knowledge of standard and advanced test and data acquisition equipment
Design, implement, and tune control software for robotic motion and interaction, collaborating with hardware and software teams to deliver reliable behavior.
The Senior Field Applications Engineer is responsible for technical support for customers PCB designers and manufacturing groups, interfacing with customers early in the design cycle to provide feedback on routing, layout, signal integrity, cost trade-off analysis, material selection, and mechanical requirements.
Compensation
A reasonable estimate of the current range is: $109,841 - $193,168
Responsibilities
Educate customer designers and technologist on Design for Manufacture (DFM) and Design for Value (DFV)
Reduce customers’ design cycle time by facilitating/eliminating problem disposition between TTM’s pre-production engineering groups and the customer
Improve the quality and completeness of design packages coming from the customer by identifying design problems related to manufacturability and reliability test
Update customer designers and manufacturing groups on TTM capabilities and set roadmap/technology direction
Thorough understanding of TTM manufacturing capabilities and technologies to support QTA/NPI/High Volume Manufacturing
Requirements
Bachelor Degree in Engineering or related discipline
Educate customer designers and technologist on Design for Manufacture (DFM), Design for Value (DFV)
Reduce customers’ design cycle time by facilitating/eliminating problem disposition between TTM’s pre-production engineering groups and the customer
Improve the quality and completeness of design packages coming from the customer and help them by identifying design problems related to manufacturability and reliability test
Update customer designers and manufacturing groups on TTM capabilities. Set roadmap and technology direction through formal customer presentations.
Analyze customer designs for manufacturability, controlled impedance, and specification improvements
Requirements
Bachelor Degree in Engineering or related discipline
Electrical Engineer I/IINewAntares · Los Angeles, US
RF Engineer Intern - QuantumNewKeysight · Santa Rosa, US
Senior / Staff Robotics Controls EngineerRoboForce · Milpitas, US