Electrical Engineer focused on AC/DC power distribution, electrical system integration, and cable assembly design for advanced semiconductor equipment.
Compensation
Base Pay Range: $76,300.00 - $129,700.00
Responsibilities
Design and develop AC/DC power distribution systems, electrical modules, and integrated subsystems.
Design systems ranging from low-voltage DC through 120-480 VAC single- and three-phase power.
Perform electrical engineering analysis, including load calculations, circuit and wire sizing, voltage drop, protection-device selection, power dissipation, and load balancing.
Design cable assemblies and wiring harnesses, including wire sizing, connector selection, pinouts, shielding, grounding, and routing requirements.
Create and maintain electrical schematics, wiring diagrams, cable drawings, BOMs, specifications, and test procedures.
Requirements
Bachelor's or Master's degree in Electrical Engineering or a related technical field
Nice to have: 480 VAC three-phase power distribution
Nice to have: Industrial electrical systems
Nice to have: Electrical design for industrial machinery
Local Combination Driver responsible for delivering products to retailers on a set route, unloading trucks, stocking shelves and coolers, and maintaining a safe driving record.
Compensation
Pay starting at $29.26 per hour. The employee will move to a higher rate of $30.84 per hour in the quarter after their 6 month anniversary.
Responsibilities
Deliver products to small and large retailers on a set route
Unload trucks using hand dolly or electric pallet jack
Stock shelves and coolers as requested
Maintain a safe driving record and comply with DOT regulations
Requirements
High school diploma or general equivalency diploma (GED)
Support sustaining of released Metrology products, introduce new designs and create upgrades impacting both Manufacturing and Service environments, focusing on electrical/electronics and electro-mechanical subsystems.
Compensation
Base Salary Range: $128,000.00 - $192,000.00, offered in good faith and based on experience, location, and qualifications. Additional Rewards: Annual bonus opportunities and potential long-term incentives tied to both company and individual success.
Responsibilities
Designs & develops electrical/electronic/electro-mechanical solutions for released products
Engineering support of products throughout the Product’s Lifecycle
Creates and evolves fixturing in support of critical part performance
Evolves product and process design to prevent failure trends
Validates and/or generates specification of components for existing designs
Completes heavy equipment transports primarily in the Midwest region, using inventory software to maintain accurate records of transports. Additionally, this position works in Truck Service as required, refurbishing, servicing and maintaining equipment, troubleshooting vehicle and equipment issues and performing welding and fabrication work.
Responsibilities
Lift and transport heavy equipment and products in a crane truck, semi, or similar multi-axle vehicle
Load and unload products at location
Maintain required paperwork and logs of all assigned transports
Maintain truck and equipment in a neat and clean condition
Conduct pre-trip and post-trip inspections and report any truck safety issues immediately to supervisor
Local UDS Driver responsible for delivering products to small retailers on a set route, unloading trucks, stocking shelves and coolers, and maintaining customer rapport.
Compensation
Pay starting at $28.14 per hour. The employee will move to a higher rate of $29.60 per hour in the quarter after their 6 month anniversary.
Responsibilities
Deliver products to small retailers on set routes
Unload trucks using hand dolly
Stock shelves and coolers as requested
Maintain customer rapport
Lift, push, and pull cases of products
Requirements
High school diploma or general equivalency diploma (GED)
CDL-A Driver for the Trench Division responsible for transporting trench and MAP shoring using knuckle boom flatbeds, semis, and trailer trucks, as well as equipment maintenance.
Compensation
$27.25 -$36.80 based on experience PAID WEEKLY!
Responsibilities
Transport Trench and MAP shoring to and from customer job sites using various trucks (knuckle boom flat bed, semi, trailer trucks)
Assembly, testing, and inspection of equipment
Power washing
Inventory control
Yard duties
Requirements
Nice to have: Previous Equipment Rental experience
Warehouse Crane Truck Driver/MechanicMFA Oil Company · Moberly, US
Class A-CDL DriverMidland Garage Door · Springfield, US
Mechanical Design Engineer - Capital EquipmentCelestica International Inc. · Remote, US+7 more