Lead the Calibration & Automation team to maintain critical instrumentation, precision scales, and process equipment controls for safety, compliance, uptime, and business continuity.
Compensation
The estimated annualized pay range for this position in Ontario is $76,400.00–$114,575.00.
Responsibilities
Coach, develop, and manage team performance.
Lead daily huddles, assign priorities, and ensure calibration deadlines are met.
Support staffing, overtime control, and continuous improvement.
Ensure GMP, 21 CFR Part 11, SOP, validation, and data integrity compliance for process equipment controls.
Support audits and inspections, and manage deviations, CAPAs, and investigations.
Requirements
High School diploma or equivalent required; licensed tradesperson in Electrical (309A or 442A), Instrumentation (447A), Mechanical (433A), or related discipline required.
Post‑secondary diploma or degree in a related field would be an asset.
Nice to have: post‑secondary diploma or degree in a related field
Collaborate on and evolve the motion-control architecture for next-generation Abi robots
Design, implement, tune, and validate control loops, trajectory generation, motion profiles, filtering, calibration, and actuator limits
Translate high-level movement and expressive-behaviour intent into reliable, physically achievable trajectories and control commands
Develop robust interfaces between motion controls, embedded firmware, motor controllers, ROS/ROS2, autonomy, perception, and higher-level behaviour systems
Help migrate latency-sensitive and safety-critical control functions from edge compute onto microcontrollers and real-time operating systems
Requirements
Bachelor’s degree in Robotics, Mechatronics, Electrical Engineering, Mechanical Engineering, Computer Science, or a related field, or equivalent practical experience
Nice to have: microcontrollers
Nice to have: RTOS-based firmware
Nice to have: migrating control functions from Linux to embedded hardware
Lead EDI CLEO and MFT Software Engineer supports enterprise-level B2B integration and secure file transfer operations across critical supply chain and logistics systems.
Responsibilities
Design, configure, and maintain CLEO MFT integration solutions and enterprise B2B file transfer workflows.
Develop and optimize complex EDI maps across standard formats, including ANSI X12 and EDIFACT.
Configure, test, and manage secure communication protocols such as AS2, SFTP, and FTPS for trading partner onboarding.
Deliver L2/L3 production engineering support, proactive system monitoring, and rapid incident triage to maintain strict SLA compliance.
Execute application remediation, bug fixes, and performance tuning within an Agile SDLC framework.
Requirements
Nice to have: Cleo CE205 Developer Certification
Nice to have: Application Remediation & Agile SDLC processes
Nice to have: Logistics & Transportation domain experience
Nice to have: L2/L3 Production Engineering & Incident Management
Lead and contribute to embedded software design, development, debugging, integration, and testing for CNS Radar systems.
Responsibilities
Lead and contribute to embedded software design, development, debugging, integration, and testing for CNS Radar systems.
Develop and maintain a strong understanding of system behavior, including radar operating modes, state transitions, timing behavior, data flow, interface interactions, fault detection, fault isolation, and recovery mechanisms.
Analyze system and software requirements and translate them into high-quality high-level requirements, low-level requirements, architecture, detailed design, code, and verification artifacts.
Perform system-level software integration on target hardware, engineering benches, system integration labs, and simulation environments.
Support system testing by defining test scenarios, executing test procedures, analyzing logs, comparing expected versus actual system responses, and driving closure of software or interface-related anomalies.
Requirements
Bachelor’s or Master’s degree in Electronics Engineering, Electrical Engineering, Computer Engineering, Aerospace Engineering, or a related technical discipline.
Lead and contribute to embedded software design, development, debugging, integration, and testing for CNS Radar systems.
Develop and maintain a strong understanding of system behavior, including radar operating modes, state transitions, timing behavior, data flow, interface interactions, fault detection, fault isolation, and recovery mechanisms.
Analyze system and software requirements and translate them into high-quality high-level requirements, low-level requirements, architecture, detailed design, code, and verification artifacts.
Perform system-level software integration on target hardware, engineering benches, system integration labs, and simulation environments.
Support system testing by defining test scenarios, executing test procedures, analyzing logs, comparing expected versus actual system responses, and driving closure of software or interface-related anomalies.
Requirements
Bachelor’s or Master’s degree in Electronics Engineering, Electrical Engineering, Computer Engineering, Aerospace Engineering, or a related technical discipline.
Natural Soda Inc (a Huber company) seeks an Electrical Engineer for our Rifle, CO location to support and lead major project management, maintenance planning, scheduling, budgeting and supervision. Provide engineering support for electrical systems, including power distribution, motor controls, instrumentation, and process automation.
Compensation
[$128,669.00 - $128,669.00]
In addition to base compensation, individuals may be eligible for an annual discretionary bonus and profit-sharing payout.
Responsibilities
Develop and execute design and modification projects to improve equipment reliability, plant safety, and energy efficiency.
Support capital projects from concept through implementation, including scope development, cost estimation, vendor coordination, and commissioning.
Conduct troubleshooting and root cause analysis for electrical equipment failures and implement corrective actions.
Ensure compliance with all regulatory, safety, and environmental requirements.
Collaborate with maintenance and operations teams to develop preventive and predictive maintenance strategies for electrical equipment and ensure complete documentation of maintenance activities.
Instrumentation and Controls Project EngineerAffiliated Engineers, Inc. · Denver, US
Leadership Development Program- Wind OperationsNextEra Energy · Raleigh, US+1 more
Electrical EngineerJM Huber Corporation · Rifle, US