Test Engineer supporting contract manufacturing partners in Penang, Malaysia, focusing on manufacturing efficiency, yield improvement, and root cause analysis.
Responsibilities
Provide daily onsite support for the production line at contract manufacturing facilities
Debug PCBAs and conduct root cause analysis on test failures and yield losses
Collaborate with Product Engineering and Supply Chain Engineering teams to address product, component, manufacturing, and test-related challenges
Manage hard cord/aging board in queue
Requirements
Bachelor’s degree in electrical engineering, Electronics Engineering, or related technical discipline
Independently performs complex assembly, inspection, testing, troubleshooting, and rework while following established engineering, safety, and quality requirements for pilot and pre-production operations involving electronic products, electromechanical assemblies, munitions, and associated support equipment.
Compensation
Pay Range: $31.00 - $36.00 per hour (Depending on experience and qualifications)
Responsibilities
Assemble and inspect electrical, electronic, electromechanical, and cable/harness assemblies using approved drawings, specifications, and work instructions
Interpret engineering drawings, schematics, wiring diagrams, connector pinouts, bills of material, and test procedures
Operate test instruments, cable/harness testers, and automated test equipment; interpret and document results
Perform fault isolation, troubleshooting, and rework within approved procedures
Support first-article and production verification activities, product transitions, and continuous improvement efforts
Requirements
High school diploma or GED
two-year technical degree/diploma
Nice to have: IPC J-STD-001 soldering certification
Nice to have: IPC/WHMA-A-620 cable and wire harness assembly certification
Nice to have: IPC-7711/7721 rework and repair training
Seeking an experienced technician to work in its Pilot & Pre-Production Lines performing electro-mechanical assembly of electronic products and support equipment.
Responsibilities
Independently assemble and inspect complex electrical/electronic and electromechanical assemblies and cable/harness builds to approved requirements.
Interpret drawings, schematics, connector pinouts, wiring diagrams, bills of material, and test procedures.
Operate and interpret results from applicable test instruments, cable/harness testers (including Cirris-type systems where used), and automated test equipment (ATE).
Perform systematic fault isolation and troubleshooting within approved procedures; document symptoms, test evidence, and results.
Support first-article or production verification activities, identify recurring build/test issues, and provide clear feedback to Engineering and Quality.
Requirements
High school diploma/GED
two-year technical degree/diploma
Nice to have: IPC J-STD-001 soldering workmanship certification
Nice to have: IPC/WHMA-A-620 cable and wire harness assembly certification
Nice to have: IPC-7711/7721 rework/repair training
The Assembler performs a combination of assembly, welding, molding, and testing operations on electromechanical medical devices, including implantable pulse generators and external peripherals, in compliance with FDA and quality system requirements.
Responsibilities
Perform electronic, mechanical, and molded assembly operations using microscopes, precision hand tools, and fixtures
Assemble, solder, weld, bond, coat, and test medical devices and related components according to documented procedures
Operate automated and manual test equipment to verify product functionality
Conduct visual and functional inspections to identify defects, nonconformances, or cosmetic issues
Perform rework and minor repairs in accordance with approved processes and work instructions
Requirements
High School Diploma or GED
Nice to have: Medical device manufacturing experience
Conducts evaluation, diagnostic, integration and final acceptance testing of airborne, commercial, surface ship and sub-surface vessel electronic equipment using established procedures.
Compensation
In compliance with pay transparency requirements, the salary range for this role in California is $57,000- $106,000.
Responsibilities
Tests and troubleshoots complex Printed Wiring Assemblies, Subassemblies, Modules and Systems using Functional Test Procedures, Individual Acceptance Test Procedures, Technical Repair Standard Procedures, Quality Test Instructions, Return Acceptance Test Procedures, and Factory Acceptance Test Procedures.
Performs Factory Acceptance Test of completed systems using Quality Test Instructions and Factory Acceptance Test Procedures.
Identifies non-conforming material and initiates Material Discrepancy Reports, FR/FF reports in TipQA, and Break-Out Shop Orders, as applicable.
Programs and verifies programmable integrated circuits using approved procedures and Quality Assurance software.
Identifies and initiates changes to test documents using a Quality Test Change Request form.
Requirements
High School Diploma or equivalent
Associate’s degree
Nice to have: Ability to read and interpret safety rules, operating and maintenance instructions, and procedure manuals
Nice to have: Ability to write routine reports and correspondence
Nice to have: Ability to speak effectively before groups of employees of organization
Independently completes complex assigned assembly and test work within approved procedures and supports troubleshooting, production verification, and the development of less-experienced technicians.
Responsibilities
Independently assemble and inspect complex electrical/electronic and electromechanical assemblies and cable/harness builds to approved requirements
Interpret drawings, schematics, connector pinouts, wiring diagrams, bills of material, and test procedures
Operate and interpret results from applicable test instruments, cable/harness testers (including Cirris-type systems where used), and automated test equipment (ATE)
Perform systematic fault isolation and troubleshooting within approved procedures
Support first-article or production verification activities, identify recurring build/test issues, and provide clear feedback to Engineering and Quality
Requirements
High school diploma/GED plus approximately 3–5 years of relevant experience
two-year technical degree/diploma plus relevant hands-on experience
Test EngineerNewTeradyne · Bayan Lepas, Malaysia
04 - Production Technical Operator 4NewCelestica International Inc. · Johor Bahru, Malaysia
Manufacturing Test Technician CNewL3HHCM20 · Anaheim, US